Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a tại Lotte Market

Thương hiệu: | Xem thêm Thiết Bị Mạng Thương hiệu  

Mô tả ngắn về Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a tại Lotte Market

Double BTS7960 43A H-bridge High-power Motor Driver Module/ Diy Smart Car Current Diagnostic. This driver uses chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 large current (43 A) H bridge driver;. 5V power indicator on board;. can solder heat sink;. RPWM: Right Turn PWM. R_EN: Right Turn Enable (High Active). R_IS: Right
: Còn hàng
: Shopee
94.247đ 159.740đ
** Quét mã QR bằng Zalo để mua trên điện thoại

Giới thiệu Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a tại Lotte Market

Double BTS7960 43A H-bridge High-power Motor Driver Module/ Diy Smart Car Current DiagnosticMô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a

BTS7960B H-bridge 43A high-power motor driver Module Overview:
This driver uses chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A
Features:
Double BTS7960 large current (43 A) H bridge driver;
5V isolate with MCU, and effectively protect MCU;
5V power indicator on board;
voltage indication of motor driver output end;Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a
can solder heat sink;
PIN Definition:
1. RPWM: Right Turn PWM
2. LPWM: Left Turn PWM
3. R_EN: Right Turn Enable (High Active)
4. L_EN: Left Turn Enable (High Active)
5. R_IS: Right Turn Current Warning (May Leave Floating)
6. L_IS: Left Turn Current Warning (May Leave Floating)Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a
7. VCC: (5V)
8. GND

Connections:
Method 1:
VCC: 5V from Microcontroller(MCU)
GND: GND from Microcontroller(MCU)
L_PWM: PWM or 5V from Microcontroller(MCU) for CCW(CW) TurnsMô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a
R_PWM: PWM or 5V from Microcontroller(MCU) for CW(CCW) Turns
R_EN and L_EN: 5V from Microcontroller(MCU)
Method 2:
VCC: 5V from Microcontroller(MCU)
GND: GND from Microcontroller(MCU)
L_PWM: 5V from Microcontroller(MCU) for CCW(CW) Turns
R_PWM: 5V from Microcontroller(MCU) for CW(CCW) Turns
Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a
R_EN and L_EN: PWM from Microcontroller(MCU)



Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2);
isolation chip 5 V power supply (can share with MCU 5 V);
size: 4 * 5 * 1.2 cm;
Able to reverse the motor forward, two PWM input frequency up to 25kHZ;Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a
two heat flow passing through an error signal output;
isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply;
the supply voltage 5.5V to 27V;


#BTS7960 #43A #H-bridge #High-power #Motor #Driver #Module #Diy #Smart #Car #Current #Diagnostic

Chi Tiết Mô Đun Kiểm Tra Động Cơ Xe Hơi Thông Minh Bts7960 43a