Máy Bơm Dầu 12v 60w tại Lotte Market

Giới thiệu Máy Bơm Dầu 12v 60w tại Lotte Market

Chào mừng bạn đến cửa hàng của tôi

Trong cửa hàng của chúng tôi, bạn sẽ
Tận hưởng dịch vụ tốt nhất
Nhận sản phẩm tốt nhất.

Chúng tôi có
Sản phẩm chất lượng tốt nhất,
Hậu cần kịp thời nhất,

Giá cả phải chăng nhất.

Tôi hy vọng rằng bạn có một trải nghiệm mua sắm khó quên, đừng quên chú ý đến chúng tôi, sự hỗ trợ của bạn là động lực lớn nhất của chúng tôi !!!

Features:
1. Widely used in general industrial equipment.
2. It works by connecting the clamps to the 12V car-battery.
3. An ideal equipment for quick and clean oil-changes.
4. Simple on/off power switch, easy to use.

Specifications:
Rated Voltage: DC 12V
Rated Power: 60W
Maximum Pressure: Max. 0.8MPA
Maximum Flow: 5L/min
Pump Diameter: Approx. 4.8cm / 1.89”
Length: Approx. 14.5cm / 5.7”
Outlet Pipe Size(Dia.*L): Approx. 11mm*140cm / 0.43” * 55”
Inlet Pipe Diameter: Approx. 8mm & 6 mm / 0.31” & 0.24”
Inlet Pipe Length: Approx. 100cm / 39.37”
Cable Length: Approx. 30cm / 11.8”
Clips Length: Approx. 8cm / 3.15”
Main Color: Black
Application: Widely used in general industrial equipment, medical equipment, chemical equipment, shipbuilding, drinks, carpet and floor cleaning, water purification and water treatment equipment, vehicle cleaning, agricultural spraying, zo pipeline pressure, air cleaning cooling, coal and metallurgical industries
How to use:
1. Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil.
2. Connect the pump to the power, run it for a while, and observe whether the inlet and outlet is normal.
3. Open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move; then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely); as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again.)
4. After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean.
5. If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out.
Package Inculded:
1 x oil pump
1 x 11mm outlet pipe
1 x 8mm inlet pipe
1 x 6mm inlet pipe
2 x clips
Note:
1. Please allow 1-3mm error due to manual measurement. Thanks for your understanding.
2. If you want to connect this pump to AC power, you will need a power converter.
3. please use when the engine is warm, the engine oil is warm and viscosity is lower, this will be easier and faster to pump.
4. This product is not allowed to pump corrosive liquids, strong acids and strong alkaline liquids.