Card Chuyển Đổi Pci E 1 Sang 3 Pci 1x 3 Khe Cắm Pci-E 1x Sang 16 tại Lotte Market
Thương hiệu: | Xem thêm Ổ Cứng Di Động Thương hiệuMô tả ngắn về Card Chuyển Đổi Pci E 1 Sang 3 Pci 1x 3 Khe Cắm Pci-E 1x Sang 16 tại Lotte Market
PCI-E 1X 1 TO 3: If you need more than one PCI-E x1 slot on the motherboard was not any so much, it contactes you can think about it. 0 cable. But even USB 3. x single-channel bandwidth also has 250MB / s, So this stuff more than enough to give you the best slots, there will not be enough: Còn hàng
** Quét mã QR bằng Zalo để mua trên điện thoại
Giới thiệu Card Chuyển Đổi Pci E 1 Sang 3 Pci 1x 3 Khe Cắm Pci-E 1x Sang 16 tại Lotte Market
PCI-E 1X 1 TO 3: If you need more than one PCI-E x1 slot on the motherboard was not any so much, it contactes you can think about it. It consists of two parts, one main card, interface installed via PCI-E X1 on the motherboard, two equipment cards, both of which are connected together via USB 3.0 cable.The device card also uses the United States Pericom Pericom PI7C9X bridge chip, for switching PCI-E, PCI-E between.
But even USB 3.0, but also the theoretical bandwidth 5Gbps (625MB / s), one Into four Then remove the loss would only 150MB / s, and even PCI-E 1.x single-channel bandwidth also has 250MB / s, So this stuff more than enough to give you the best slots, there will not be enough bandwidth, not only for the performance requirements of the place.
Therefore, the transferred PCI-E slot is the best version above 2.0, the 3.0 version is better. Several Divided PCI-E 1X slot all is gen2 e, even if gen1 previously ,it can be ok!
Mainboard size:(LXWXH)9.60 x 6.40 x 1.30cm/3.78 x 2.52 x 0.51inch
PCI-E Card size:(LXWXH)11.80 x 6.50 x 1.90cm/4.65 x 2.56 x 0.75inch
USB cable length 60cm/1.97ft
installation:
1. The first step, first of PCIe USB card plugged into the motherboard's PCIe slot.
2. Use USB3.0 data cable adapter to connect the ends of the two USB port. Plug in the power supply.
3.The third step: After completion of the above two steps, first in no hurry to insert your PCI-E card, start the computer to see if your computer has been identified to the riser card, if you did not find the card, repeat the above operation (Note: The first time to insert card to start the computer, into the system in general will be prompted to install new hardware, such as ”PCI standard PCI-to-PCI bridge” , you need to wait for it to automatically install the complete, individual anti-virus software will prevent these files installation, note skipped), when your computer has been recognized the card,blue LED PCI slot on normal light, computer equipment manager in the system device will show an increase of several ”PCI standard PCI-to-PCI bridge
4. After completing the above three steps, turn off the computer, plug in your PCI-E card, to be careful not to insert the contrary, then boot into the system, install Driver
colour:Blue
Material:PCB
Package Contents:
1 x Mainboard
1 x PCIe card
1 x USB white cable
1set x Screw
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.